Product Details:
|
Main Material: | Bitumen, Polyester Felt, Fiberglass Felt | Surface Treatment: | PE Film, Aluminum Foil, Mineral Granule |
---|---|---|---|
Tyre: | Polyester Mat, Fiberglass | Heat Resistance: | 105degree |
Low Temperature: | -25degree | Watertightness: | 30min |
High Light: | sbs waterproofing membrane,bituminous sheet waterproofing |
Reinforced Torched On SBS Modified Bitumen Waterproof Membrane Roofing Roll
Introduction:
SBS elastomer modified bitumen waterproof membrane is based on bitumen then added styrene, butadiene, styrene, TPE as modified materials, with special process to compound high polymer modified bitumen
Characteristics:
1. Excellent low temperature performance, especially suitable for cold area application.Good weather resistance, tensile property; high elongation, wear resistance and excellent workability.
2. It has such advantages as no flow under high temperature condition,being soft under low temperature condition,being high flexible and aging resistant.
3. Thus the flex durability,flexibility and cohesive force of the asphalt is largely improved.
4. Therefore,the waterproof quality of the buildings improves a lot and service time also prolongs.
Describation width(m) length (m) weight (kg/roll) thickness (mm)
SBS modified Asphalt waterproof Membrane 1 10 28 2
SBS modified Asphalt waterproof Membrane 1 10 41 3
SBS modified Asphalt waterproof Membrane 1 8 48 4
SBS modified Asphalt waterproof Membrane 1 10 32 2
with mineral granules
SBS modified Asphalt waterproof Membrane 1 10 43 3
with mineral granules
SBS modified Asphalt waterproof Membrane 1 8 50 4
with mineral granules
SBS modified Asphalt waterproof Membrane 1 10 28 2
with aluminum oil
SBS modified Asphalt waterproof Membrane 1 10 41 3
with aluminum oil
SBS modified Asphalt waterproof Membrane 1 8 48 4
with aluminum oil
Specifications:
1. Type:Type Ⅰ,Type Ⅱ
2. Base felt:PY/G
3. Upper surface material:PE/Mineral/Aluminum foil
4. Thickness:2mm-5mm or according to customer’s requirement
Features
Good capacity of anti-aging, anti-acid, and anti-alkali, its service life is 30years.
High tensile strength and elongation which adapts to the contraction or crack of the base.
Good perdurable capacity to climate; be used in cold(-25°C)environment for long life.
Applied by torch.
Widely applied in roofing, basement, pool, subway etc.
Construction Requirements Basement Treatment
The waterproofing base should be strong smooth, and clean without particles on the surface. No peeling or cracking shall exist on the surface. The corners of the base shall be made into arcs with a radius of no less than 20mm or triangular. The drain slope, division seam, and air vent shall be carried out and treated according to design requirements. Then brush promer on the foundation until it is dry.
Technical Datasheet
No. |
item |
Ⅰ |
Ⅱ |
|||||||||
PY |
G |
PY |
G |
PYG |
||||||||
1 |
Soluble content /(g/sqm) |
3mm |
2100 |
* |
||||||||
4mm |
2900 |
* |
||||||||||
5mm |
3500 |
|
||||||||||
Test phenomenon |
* |
Nonflammable |
* |
nonflammable |
* |
|||||||
2 |
Heat resistance |
°C |
90 |
105 |
||||||||
≤mm |
2 |
|||||||||||
Test phenomenon |
No flow , no drip |
|||||||||||
3 |
Low temperature flexibility/°C |
-20 |
-25 |
|||||||||
No cracks |
||||||||||||
4 |
Impermeability/(30min) |
0.3Mpa |
0.2Mpa |
0.3Mpa |
||||||||
5 |
Tension (N/50mm) |
Maximum tension≥ |
500 |
350 |
800 |
500 |
900 |
|||||
Second high tension≥
|
* |
* |
* |
* |
800 |
|||||||
Test phenomenon |
While pulling,bitumen will not crack or separate with the felt |
|||||||||||
6 |
elongation |
Maximum elongation≥ |
30 |
* |
40 |
* |
* |
|||||
Second high elongation ≥ |
* |
* |
15 |
|||||||||
7 |
Peel strength between the coiled material(N/mm) |
1.5 |
Installation:
Place the sheet correctly, fire torch, evenly heat the sheet and foundation ,When the surface of the sheet is black and bright with a fusion layer apply the sheet and press it into a solid and flat state. Before the sheet is cool, seal the edge of joints by float.
Cautions installation is forbidden during rain, snow, fog, strong wind.
The temperature should be 5-35°C during installation.
All nodes should be reinforced during installation.
Keep away from fire during storage.
Contact Person: Angela
Tel: 008615511775265